How To: Apply a Motocross Graphics Kit
Ever purchased a mud bike graphics kit to freshen up your motocross bike, however been too scared to put it on for concern of destroying it in the process? Listed below are the secrets we now have been utilizing for years to get graphics on quickly and easily.
What are the options?
The old saying goes there are a few different ways to skin a cat, which additionally applies to sticker kits as there isn’t really a right or mistaken way to do this. We've got advised the following technique as it has ended up being the simplest way we have now experienced while getting good results, and may be cleaner than another ways involving soapy water to help getting the graphics on straight.
Other alternate options for applying graphics to the bike utilizing nothing but elbow grease, which can work out fine, however for those who haven’t utilized graphics earlier than we wouldn’t advocate it! The downside is the graphics are sticky and not very malleable, so you'll have to get them straight the primary attempt or you might damage the kit making an attempt to tear them off to get them straight.
Another technique is the wet application using soapy water to lubricate the plastics and the sticker kit so you'll be able to place the graphics on and slide them around until you will have them within the correct place. The downside is a few imagine that even though the soapy water dries, there may be always cleaning soap residue the remains beneath the dust bike graphics kit, compromising the adhesive power and making the kit more likely to peel off over time.
Step 1: Remove the old graphic kit from areas which you want to apply graphics to, you need a clean and smooth surface for one of the best probability of your graphics looking good and staying on. There may be some glue residue left in your plastics which is best to clean off with an alcohol-primarily based cleaner - it's vital not to use any oil-based cleaners, as this can damage the glue after installation.
Step 2: When your bike is clean and dry, take your whole new graphics out of the packaging and work out where every piece needs to go, it may be confusing generally with similarly formed dirt bike stickers, so a good way to recollect is working everything out after which laying them on the ground within the sample which they are going to go onto your bike.
Step three: You might be ready to start making use of! Choose a part of the bike which is smooth and relatively flat on your first attempt slightly than picking a rounded surface which may be tricky, we normally start on the entrance fender and work our way to the back of the bike from there.
Some folks like to remove the plastics from the bike to apply graphics, however we've got discovered that on a full kit, some parts of the bike won’t line up perfectly straight, so keeping the plastics on the bike will aid you get everything lining up straighter. You might wish to remove your seat or sure pieces of plastic momentarily as some graphics are designed to fold over an edge and stick down on the top of your fuel tank for instance, which would be harder with your seat nonetheless attached.
Begin by holding the sticker to the desired location to see how well it will line up and the place you want it to stick. Once you are joyful, peel away a small section of the backing paper so you have a small section of adhesive exposed. We always find a straight section to start on as when you line the first part up properly the remainder of the sticker ought to line up correctly with the plastic providing the sticker template is made well.
After you have a small section stuck to the plastic and before you remove the remainder of the sticker backing check to see if the sticker is lining up with the remainder of the plastic by holding it down to see the place it lines up. If you are happy you're ready to finish this off, if not you possibly can lift the sticker off and have another attempt till you get it proper!
This is the place the heat gun comes into play:
Take your heat gun or hair dryer set on a low setting and use it to warm the motocross graphics up on the edge which is being stuck down, hold the heat gun approximately 30cm from the target as stickers are thin, so that they don’t need a lot heat before they start to melt - take your time and be careful or you'll end up with a warped mess!
As you warm the sticker up you possibly can slowly peel the backing paper off and work the sticker down using your fingers, you can find the sticker is soft because of the heat and can mould to the form of the plastics easily. Because of the warmth, it shall be less likely to bubble and the sticker can stretch or compress simply and kind to the form you need it to.
Keep doing this until the sticker is completely on and you should have a straight, smooth sticker free from bubbles, and don't have any need to use a box cutter to trim the loose parts of your sticker kit.
Repeat this process on each panel however bear in mind a surface which is concave or convex will always be troublesome to apply without bubbles, some stickers for these panels come with a small part lower out to allow for an overlap. It's possible you'll need to trim these further so do your best and don’t be scared to trim if need be!
If you beloved this article and you simply would like to get more info about sur-ron sticker kits please visit our own internet site.
Forum Role: Participant
Topics Started: 0
Replies Created: 0